Troy-bilt CS4210 Manual de usuario descargar pdf

Operator’s Manual

Chipper / Shredder

Models CS4210

CS4265

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

MTD LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-

covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if

any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required

by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark

arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131

Cleveland, Ohio 44136-0019.

PRINTED IN U.S.A.

FORM NO.

769-00830.fm

(7/03)

Model CS4210 Shown

1 2 3 4 5 6 ... 12 13

Indice de contenidos

Pagina 1 - Operator’s Manual

Operator’s ManualChipper / ShredderModels CS4210CS4265IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD LLC P.O. BOX 361131 CLEVELAND, OHIO 4

Pagina 2 - CALLING CUSTOMER SUPPORT

10Discharge Chute: Lubricate the pivot points on the chute deflector with light oil once a season. Engine: Refer to the Briggs & Stratton Owner

Pagina 3 - PREPARATION

11Figure 9NOTE: Use a 3/16” hex key (Allen) wrench on the outside of the blade and a 1/2” box (or socket) wrench on the inside of the impeller. See F

Pagina 4 - MAINTENANCE AND STORAGE

12Storing Your Chipper Shredder• Clean the equipment thoroughly.• Wipe equipment with an oiled rag to prevent rust.• Refer to engine manual for correc

Pagina 5 - Lowering the Chipper Chute

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used

Pagina 6 - (Model CS4210 Only)

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices ... 3Assembling

Pagina 7 - Starting Engine

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th

Pagina 8 - Stopping Engine

4i. Never store the machine or fuel container inside where there is an open flame, spark, or pilot light (e.g. furnace, water heater, space heater, cl

Pagina 9 - Customer Responsibilities

5SAFETY LABELS FOUND ON YOUR UNITSECTION 2: ASSEMBLING YOUR CHIPPER SHREDDERIMPORTANT: This unit is shipped without gasoline or oil in the engine. B

Pagina 10 - Replacing the Chipper Blades

6Attaching The Debris Collection Bag• To attach the bag, place the opening of the bag completely over the discharge chute.• Position the bag so that t

Pagina 11 - Replacing the Shredder Blade

7Figure 4SECTION 4: OPERATING YOUR CHIPPER SHREDDER WARNING: The operation of any chippershredder can result in foreign objects beingthrown. Always

Pagina 12 - SECTION 6: TROUBLESHOOTING

8• Grasp the starter handle and pull the rope out slowly until resistance is felt. When it becomes slightly harder to pull the rope, slowly allow the

Pagina 13

9• Use the tamper to assist in feeding branches into the chipper chute.• Apply intermittent pressure (force, in short pulses) while feeding larger (2-