Troy-Bilt LS338 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Cortadoras De Troncos Troy-Bilt LS338. Troy-Bilt LS338 User's Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 18
  • Tabla de contenidos
  • SOLUCIÓN DE PROBLEMAS
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
PRINTED IN U.S.A.
FORM NO
.
769-00089A.fm
(10/2002)
Operators Manual
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
TROY-BILT LLC. P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
Log Splitter
Model LS338
Vista de pagina 0
1 2 3 4 5 6 ... 17 18

Indice de contenidos

Pagina 1 - Operator’s Manual

PRINTED IN U.S.A.FORM NO. 769-00089A.fm(10/2002)Operator’s ManualIMPORTANT: Read safety rules and instructions carefully before operating equipment.TR

Pagina 2 - CALLING CUSTOMER SUPPORT

10SECTION 4: OPERATING YOUR LOG SPLITTER Gas and Oil Fill-Up• Service the engine with gasoline and oil as instructed in the engine manual packed with

Pagina 3

11• To lock the beam in the vertical position, pull out on the vertical beam lock and rotate it to secure the beam. See Figure 13.• Stand in front of

Pagina 4 - Your Responsibility

12SECTION 5: ADJUSTING YOUR LOG SPLITTERWedge Assembly AdjustmentAs normal wear occurs and there is excessive “play” between the wedge and beam, adju

Pagina 5 - Attaching Jack Stand

13kerosene whenever any repair work is performed on the tank, hydraulic pump or valve. For this job, contact your nearest service dealer. Hydraulic Fi

Pagina 6 - Attaching the Tongue

14SECTION 7: STORING YOUR LOG SPLITTERPrepare your log splitter for storage at the end of the season or if the log splitter will not be used for 30 d

Pagina 7 - Attaching The Hoses

15Hydraulic TroubleshootingNOTE: For repairs beyond those listed here, contact your nearest authorized service center.Problem Cause RemedyCylinder rod

Pagina 8 - Preparing the Log Splitter

16SECTION 9: PARTS LIST FOR MODEL LS33890474248478941874638394036371516926613252732303386127879802221232420111092728312981465663434445828384856865666

Pagina 9 - Stopping Engine

17Model LS338 Ref. No.Part No. Part Description1.781-0686 Log Tray Bracket3.781-0682 Log Tray4.710-3097 Carriage Bolt 3/8-16 x 1.05.719-0550 Wedge Ass

Pagina 10 - Using the Log Splitter

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used

Pagina 11 - Transporting the Log Splitter

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices... 3Assembling Your L

Pagina 12 - Wedge Assembly Adjustment

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESGeneral Practices1. Read, understand, and follow all instructions on the machine and in the manual(s) b

Pagina 13 - Flexible Pump Coupler

4equipment. move machine to another area. Wait 5 minutes before starting the engine.i. Never store the machine or fuel container inside where there is

Pagina 14 - SECTION 8: TROUBLESHOOTING

5SECTION 2: ASSEMBLING YOUR LOG SPLITTERUnpacking from Crate• Pry top, sides, and ends off the crate. Set panels aside to avoid tire puncture or pers

Pagina 15 - Hydraulic Troubleshooting

6• Insert hex bolts through top holes in jack stand mounting brackets and holes in jack stand. Secure with lock washers and hex nuts. See Figure 3.• I

Pagina 16

7Attaching Beam • For shipping purposes, the pressure hose is attached to the pump on the engine and to the control valve on the cylinder.• Disconnect

Pagina 17 - Model LS338

8• Remove the protective cap from the fitting on top of the filter head. Attach the end of the hose to the fitting on top of the filter. Place the hos

Pagina 18

9SECTION 3: KNOW YOUR LOG SPLITTERCompare the illustration in Figure 13 below with the controls on your log splitter, and get familiar with its feat

Comentarios a estos manuales

Sin comentarios